3 electronic solutions division interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? mini d ribbon (mdr) cable assembly .050" high speed digital camera link ? cable C right angle 14h26-szlx-xxx-0lc ? supports industrial camera link ? standard for camera to frame grabber communications ? space-saving right angle cable exit ? 11 shielded twin-ax pairs and four drain wires ? entire cable bundle is shielded with foil and braid for additional signal protection ? rugged mdr ribbon type contact ? rugged thumbscrew retention ? emi shielded junction shell on straight end ? emi shielded overmolded shell on right-angle end ? see regulatory information appendix (ria) for chemical compliance information date modifed: january 20, 2009 ts-2262-c sheet 1 of 3 physical connector contact plating: wiping area: 30 " [0.76 m] min. gold (ria e1 & c1 apply) overmolded shell: color: black material: polyvinyl chloride (pvc) shell: color: beige material: polyester elastomer cable: color: beige jacket material: polyvinyl chloride (pvc) flammability: awm vw-1 electrical voltage rating: 30 v current rating: 1 a insulation resistance: > 1 x 10 8 at 100 v dc withstanding voltage: 350 v rms for 1 minute individually shielded twisted pairs characteristic impedence: 100 10 conductor size: 28 awg stranded propagation velocity: 1.25 ns/ft [4.1 ns/m ] skew (within pair): 50 ps/meter maximum skew (channel skew per chipset): 50 ps/meter maximum environmental temperature rating: -20c to +75c ul file no.: e86982 camera link is a certifcation mark of automated imaging association.
3 electronic solutions division interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? mini d ribbon (mdr) cable assembly .050" high speed digital camera link ? cable C right angle 14h26-szlx-xxx-0lc ts-2262-c sheet 2 of 3 mm [inch] tolerance unless noted 0.0 0.00 mm .1 .01 [ ] dimensions for reference only c a b l e l e n g t h t o l e r a n c e i s t h e l a r g e r o f + 5 0 m m / - 0 m m o r + 3 % / - 0 % r i g h t - a n g l e e n d s t r a i g h t e n d 2 x 2 6 p o s i t i o n h i g h d e n s i t y m i n i d r i b b o n ( m d r ) m a l e p l u g 4 2 . 4 [ 1 . 6 7 ] c a b l e l e n g t h 1 2 . 8 [ 0 . 5 1 ] 3 9 . 7 [ 1 . 5 6 ] 3 9 . 7 [ 1 . 5 6 ] 1 9 . 4 [ 0 . 7 6 ] 3 2 . 5 [ 1 . 2 8 ] # 4 - 4 0 t h u m b s c r e w s 1 4 h 2 6 - s z l m - x x x - 0 l c 1 4 h 2 6 - s z l s - x x x - 0 l c m d r 2 6 p o s i t i o n p l u g r i g h t - a n g l e e n d m d r 2 6 p o s i t i o n p l u g s tr a i g h t e n d 1 1 3 1 4 2 6 use 3m ? jacketsocket 3341-31 for mounting receptacle to panel. ordering information 14h26 - szlx - xxx - 0lc right-angle orientation m = position 1 opposite cable s = position 1 on cable side cable length 050 = 50 cm 300 = 300 cm 600 = 600 cm 100 = 100 cm 350 = 350 cm 700 = 700 cm 150 = 150 cm 400 = 400 cm 800 = 800 cm 200 = 200 cm 450 = 450 cm 900 = 900 cm 250 = 250 cm 500 = 500 cm a00 = 1000 cm for lengths greater than 1000 cm refer to table 2.
3 electronic solutions division interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? mini d ribbon (mdr) cable assembly .050" high speed digital camera link ? cable C right angle 14h26-szlx-xxx-0lc ts-2262-c sheet 3 of 3 table 1 cable assembly and camera link pinouts medium and full confgurations base confguration two channel link chips one channel link chip + camera control + serial communication camera connector frame grabber channel link signal cable name (reference only) camera connector frame grabber channel link signal 1 1 inner shield inner shield 1 1 inner shield 14 14 inner shield inner shield 14 14 inner shield 2 25 y0- pair 1- 2 25 x0- 15 12 y0+ pair 1+ 15 12 x0+ 3 24 y1- pair 2- 3 24 x1- 16 11 y1+ pair 2+ 16 11 x1+ 4 23 y2- pair 3- 4 23 x2- 17 10 y2+ pair 3+ 17 10 x2+ 5 22 yclk- pair 4- 5 22 xclk- 18 9 yclk+ pair 4+ 18 9 xclk+ 6 21 y3- pair 5- 6 21 x3- 19 8 y3+ pair 5+ 19 8 x3+ 7 20 100 ohm pair 6+ 7 20 sertc+ 20 7 terminated pair 6- 20 7 sertc- 8 19 z0- pair 7- 8 19 sertfg- 21 6 z0+ pair 7+ 21 6 sertfg+ 9 18 z1- pair 8- 9 18 cc1- 22 5 z1+ pair 8+ 22 5 cc1+ 10 17 z2- pair 9- 10 17 cc2+ 23 4 z2+ pair 9+ 23 4 cc2- 11 16 zclk- pair 10- 11 16 cc3- 24 3 zclk+ pair 10+ 24 3 cc3+ 12 15 z3- pair 11- 12 15 cc4+ 25 2 z3+ pair 11+ 25 2 cc4- 13 13 inner shield inner shield 13 13 inner shield 26 26 inner shield inner shield 26 26 inner shield notes: 1. all pairs are individually shielded with aluminum foil. 2. pair shields are wrapped aluminum out and are in contact with four internal drains (logic ground). 3. outer braid and foil (chassis ground) are isolated from inner drains (logic ground). 4. cable assembly compatible with both camera link confgurations. table 2 length codes first 2 digits alpha code first 2 digits alpha code first 2 digits alpha code 10 a 17 h 24 r 11 b 18 j 25 s 12 c 19 k 26 t 13 d 20 l 27 v 14 e 21 m 28 w 15 f 22 n 29 y 16 g 23 p 30 z for lengths in excess of 1000 cm substitute the corresponding alpha code for the frst 2 digits. example: the code for 1160 cm is b60.
regulatory information appendix 3m electronic solutions division/interconnect europe appendix e1: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product is rohs compliant 2005/95/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e2: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/747/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e3: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment as amended by commission decision 2005/618/ec. this product contains lead in the solder tail area in excess of the maximum concentration value allowed . unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e4: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec, as amended by eu commission decision 2005/717/ec, as amended by eu court of justice decision 2008/c 116/04 this product contains decabde in the insulating material in excess of the maximum concentration allowed for fnished products subject to eu rohs that are placed on the eu market after june 30, 2008. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. ria-2217b-e
appendix e5: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical and electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under item 6 of the annex to the directive. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. china appendix c1: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decabde); or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix c2: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decabde); or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. the numerical reference in the symbol above should not be construed as a representation regarding the products life or an extension of a product warranty. the product warranty is stated below. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the product warranty stated below. ria-2217b-e
important notice all statements, technical information, and recommendations related to 3ms products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. before using this product, you must evaluate it and determine if it is suitable for your intended application. you assume all risks and liability associated with such use. any statements related to the product which are not contained in 3ms current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized offcer of 3m. warranty; limited remedy; limited liability. this product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3m makes no other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. if this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3ms option, to replace or repair the 3m product or refund the purchase price of the 3m product. except where prohibited by law, 3m will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3m product, regardless of the legal theory asserted. please recycle. printed in usa. ? 3m 2008. all rights reserved. ria-2217b-e 3 3m electronics solutions division 6801 river place blvd. austin, tx 78726-9000 u.s.a. 1-800-225-5373 www.3m.com/interconnects 3m is a trademark of 3m company. appendix c3: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers (excluding decabde); or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. the numerical reference in the symbol above should not be construed as a representation regarding the products life or an extension of a product warranty. the product warranty is stated below. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the product warranty stated below.
|
